Nevada DMV CDL General Knowledge Practice Test 9

  • Questions50
  • Correct to pass40
  • Passing score80%
  • Minimum age18 years

Minimum age: 18 years for intrastate commerce; 21 years for interstate commerce

50 questions. Pick an answer to see if it is right and why; you need 40 correct answers to pass.

  1. 1. What does the working load limit stamped on a chain or strap describe?

    Show answer

    Answer B: The maximum load the device is rated to hold in normal use

    The working load limit is the rated safe capacity for everyday use, deliberately set well below the force that would break the device.

  2. 2. What is normally required in order to move an over-width or over-length load?

    Show answer

    Answer B: A special permit along with warning devices such as flags and signs

    Oversize movements need a permit plus marking devices, and travel is often limited to certain hours or routes.

  3. 3. A 60 foot combination traveling above 40 mph should hold how many seconds of following distance?

    Show answer

    Answer D: Seven seconds

    Six seconds cover the 60 feet of vehicle length, and one extra second is added because the speed is above 40 mph.

  4. 4. Your load projects more than 4 feet beyond the rear of the vehicle. How must the projecting end be marked?

    Show answer

    Answer A: With a red or orange flag by day and a red lamp after dark

    Federal rules require a warning flag on a rear projecting load in daylight and a red lamp on the end of it when lights are required.

  5. 5. Why must tiedowns be rechecked during a trip even when they were tight at the start?

    Show answer

    Answer C: Road vibration and cargo movement can loosen them as the miles go by

    Straps and chains settle and loosen as the vehicle bounces and the cargo shifts slightly, so the load must be rechecked at the required intervals.

  6. 6. You find one lug nut missing from a wheel that has ten studs. What should you do?

    Show answer

    Answer C: Treat it as a defect and have it repaired before the vehicle is driven

    Every missing fastener loads the others more heavily, and wheel separations usually begin with one nut that nobody replaced.

  7. 7. Federal rules keep recapped and retreaded tires off the front wheels of which vehicle?

    Show answer

    Answer B: Any bus carrying passengers

    The federal rule names buses: a bus may not run with regrooved, recapped or retreaded tires on its front wheels, because a steer tire failure with passengers aboard takes away steering control.

  8. 8. Most rollovers of loaded trucks on exit and entrance ramps happen for which reason?

    Show answer

    Answer B: The ramp was taken faster than the load could tolerate

    A posted ramp speed is set for cars, and a loaded trailer with a high center of gravity can roll at a speed a car would take easily.

  9. 9. You are backing into a yard where electrical wires cross overhead. What is the main concern?

    Show answer

    Answer C: The wires may hang lower than the top of your vehicle

    Overhead space has to be checked like any other space around the vehicle, because wires and cables are often lower than they look from the cab.

  10. 10. You are pulling away from the curb after a delivery. Why is a mirror check needed first?

    Show answer

    Answer B: A cyclist or a vehicle may be coming up alongside you

    Traffic and cyclists can arrive alongside a parked vehicle at any moment, so the mirrors must be checked immediately before pulling out.

  11. 11. At a stop on a hot day you find a tire that is too hot to touch. What should you do?

    Show answer

    Answer C: Wait until the tire cools before driving on, and do not let air out of it

    A tire that is too hot to touch may be about to fail or catch fire; releasing air only leaves it underinflated once it cools, which makes things worse.

  12. 12. You are pulling away from a curb in a 65 foot combination. Besides traffic, what must you watch?

    Show answer

    Answer B: The trailer wheels, which stay close to the curb and can strike it or an object on it

    Because of off-tracking, the rear wheels follow a tighter path than the front, so they stay near the curb while the cab is already out in the lane.

  13. 13. What does gross vehicle weight mean, as opposed to gross vehicle weight rating?

    Show answer

    Answer B: The actual weight of the single vehicle plus everything it is carrying

    Gross vehicle weight is what the vehicle actually weighs at that moment; the rating is the maximum the manufacturer allows it to weigh.

  14. 14. When turning left, what should a driver of a long vehicle do before beginning the turn?

    Show answer

    Answer B: Reach the center of the intersection so the rear wheels clear the corner

    The rear wheels follow a tighter path than the front, so the vehicle must reach the center of the intersection before the turn begins.

  15. 15. What is the basic rule about backing a large vehicle?

    Show answer

    Answer B: Avoid backing whenever there is another way

    Backing is dangerous because you cannot see everything behind you, so the manual tells drivers to plan routes and parking that avoid it.

  16. 16. You are asked to drive a truck loaded with enough hazardous materials to require placards. What must you have?

    Show answer

    Answer C: A hazardous materials endorsement on your commercial driver license

    Driving a vehicle that must be placarded requires the H endorsement, which involves a separate knowledge test and a security background check.

  17. 17. Which wheel or rim condition must be treated as a defect during the walkaround?

    Show answer

    Answer C: Cracks, illegal welded repairs, or missing and loose lug nuts

    Cracked or welded rims and missing or loose fasteners can let a wheel separate from the vehicle and must be corrected before driving.

  18. 18. After starting a trip, when must a driver first re-inspect the cargo and the devices holding it?

    Show answer

    Answer A: Within the first 50 miles

    Federal rules require a check of the load and its securement within the first 50 miles, because settling and vibration loosen straps and chains early in a trip.

  19. 19. When is tire pressure most accurately compared with the recommended figure?

    Show answer

    Answer B: When the tires are cold, before the vehicle has been driven

    Recommended pressures are cold pressures, so a reading taken before the tires have heated up is the only one that can be compared directly.

  20. 20. Why should a long vehicle never swing out to the left before starting a right turn?

    Show answer

    Answer D: Another driver may read it as a left turn or pass on your right

    Swinging left opens a gap on your right that a car will move into, and it also sends a false message about which way you are going.

  21. 21. Under the federal hours of service rules, when must a property-carrying driver take a 30 minute break?

    Show answer

    Answer C: After 8 cumulative hours of driving time

    Driving is not allowed after 8 cumulative hours of driving time without at least a 30 consecutive minute interruption of driving.

  22. 22. Which items belong to the in-cab part of the inspection?

    Show answer

    Answer D: Gauges, controls, mirrors, windshield, wipers, horn, heater and defroster

    The in-cab step checks the instruments and controls the driver depends on, along with mirrors, glass, wipers, horn and the heater and defroster.

  23. 23. Before starting a trip, what must the driver confirm about the weight of the loaded vehicle?

    Show answer

    Answer A: That it is within the legal gross and axle limits for the route being driven

    Overweight vehicles brake poorly, damage tires and suspension components, and can be put out of service at a scale, so weight is checked before the wheels turn.

  24. 24. You need fuel and the canopy over the pumps is low. What is the safe way to handle the clearance?

    Show answer

    Answer B: Stop and check the height at the entrance and at the way out before committing

    Clearance can differ at the entry, under the canopy and at the exit, and a sloping approach changes the effective height, so both ends have to be checked.

  25. 25. Why should you avoid using your lights to tell a following driver that it is safe to pass you?

    Show answer

    Answer B: You may misjudge the gap and the driver will act on your signal

    The manual warns against signaling others to pass, because the responsibility for a head-on crash then rests on a judgment you could easily get wrong.

  26. 26. You are dropping a loaded trailer in a yard. How far should the landing gear be lowered?

    Show answer

    Answer A: Until the pads make firm contact and the trailer weight is just off the fifth wheel

    Cranking down until the gear is firmly on the ground and just lifting the load off the fifth wheel makes the trailer stable and lets the tractor pull out cleanly.

  27. 27. What does the gross combination weight rating cover?

    Show answer

    Answer B: The maximum loaded weight of the power unit together with the trailer or trailers it tows

    The combination rating takes in the power unit and everything behind it, loaded, as specified by the manufacturer.

  28. 28. You are on a freeway and see brake lights come on in several vehicles far ahead of you. What should you do?

    Show answer

    Answer A: Ease off the accelerator and get ready to slow down

    Brake lights well ahead are an early warning that traffic is slowing, and acting on them gives a heavy vehicle the room it needs.

  29. 29. How much free play in the steering wheel is enough to make a vehicle hard to steer and should be reported?

    Show answer

    Answer B: More than 10 degrees, roughly 2 inches of movement at the rim of a 20 inch wheel

    Excess play means steering input is lost before the wheels respond, and more than about 10 degrees is treated as a defect.

  30. 30. The rear wheels of your vehicle lock during braking and the rear starts to slide sideways. What should you do first?

    Show answer

    Answer A: Stop braking so the rear wheels can roll again, then steer quickly in the direction you want to go

    Locked wheels have no side grip; releasing the brakes restores traction and then countersteering brings the vehicle back into line.

  31. 31. Why is it harder to judge speed and distance at night?

    Show answer

    Answer C: You see much less detail and have fewer reference points

    Darkness removes the visual references that the brain uses to estimate distance and closing speed, so drivers routinely misjudge both.

  32. 32. Besides slowing down, which technique most reduces the risk of a skid on a snow covered road?

    Show answer

    Answer B: Make every steering, braking and speed change gradual

    Traction is limited on snow, and sudden inputs demand more grip than the surface can supply, so smoothness is what keeps the tires attached to the road.

  33. 33. With water standing on the road, hydroplaning can begin at speeds as low as what?

    Show answer

    Answer D: 30 mph

    When enough water covers the surface, the tires can ride up on it and lose contact at speeds as low as 30 mph.

  34. 34. Under federal safety rules, what must the driver of a commercial vehicle do before starting a trip?

    Show answer

    Answer A: Be satisfied that the vehicle is in safe operating condition

    The driver is responsible for inspecting the vehicle and must be satisfied it is in safe operating condition before the trip begins.

  35. 35. Which combination of warning devices meets the requirement for a stopped commercial vehicle?

    Show answer

    Answer A: Three reflective triangles, or six fusees, or three liquid burning flares

    A vehicle may carry three bidirectional reflective triangles, six fusees or three liquid burning flares as its warning devices.

  36. 36. What are you checking on the mud flaps during the walkaround?

    Show answer

    Answer C: That they are securely attached, not torn and not dragging on the ground

    A flap that is torn or hanging loose stops shielding following traffic from spray and stones, and a dragging flap can catch and tear away on the road.

  37. 37. What is required of the hooks, rails, rings and anchor points that tiedowns attach to?

    Show answer

    Answer A: They must be part of the vehicle and strong enough for the load being secured

    A tiedown is only as strong as what it is hooked to, so anchor points must be proper vehicle fittings rated for the job.

  38. 38. You are taking a tightly curved highway exit ramp in a long combination. Where should the tractor be placed within the lane?

    Show answer

    Answer D: Toward the outside of the curve, leaving room for the trailer to track inside

    Because the trailer wheels cut to the inside of the curve, the tractor has to be kept out toward the outer edge so the trailer does not drop a wheel off the inside edge.

  39. 39. A dock crew loads all of the freight at the very back of a 48 foot van trailer. What are the two consequences?

    Show answer

    Answer A: The steering axle is relieved of weight and steering becomes light, and the trailer axles may go over the limit

    Weight placed far to the rear lifts weight off the front of the combination, so the steering goes light while the trailer axles take too much of the load.

  40. 40. How does a front tire failure usually feel to the driver?

    Show answer

    Answer D: The steering suddenly becomes heavy and pulls to one side

    A failed front tire loads the steering and makes the wheel feel heavy, while a rear tire failure shows up as the back end swaying.

  41. 41. What is the driver responsible for when a load is covered with a tarp?

    Show answer

    Answer C: Fastening it so it cannot flap free, block a mirror, or come off in the wind

    A tarp that works loose can tear away, block the driver view or the view of others, and become a hazard for the traffic behind.

  42. 42. Your brakes are starting to fade on a mountain downgrade and a sign shows an escape ramp one mile ahead. What should you do?

    Show answer

    Answer B: Plan to use the ramp instead of trying to reach the bottom

    Fading brakes on a grade only get worse, and the ramp exists precisely so a driver does not have to gamble on the rest of the descent.

  43. 43. Why should you never back under a trailer whose landing gear is resting on soft or muddy ground?

    Show answer

    Answer C: The landing gear can sink or collapse and the trailer can drop or tip over

    Soft ground lets the landing gear sink under the load being transferred to it, and a trailer that drops or topples during coupling is extremely dangerous.

  44. 44. You must leave the vehicle parked on a slight grade. What adds security beyond setting the parking brake?

    Show answer

    Answer D: Chocking the wheels so the vehicle cannot roll if the brake bleeds off

    Chocks hold the vehicle mechanically and are the standard backup whenever a parked vehicle could roll.

  45. 45. A sign before a long descent shows 6 percent. What does that number tell you?

    Show answer

    Answer A: How steep the grade ahead is

    Percent grade is the drop in feet for every hundred feet of road, so the higher the number the faster speed will build and the lower the gear you need.

  46. 46. A straight truck has a long body behind the rear axle. What happens to that overhang in a sharp left turn?

    Show answer

    Answer D: It swings out to the right and can strike a vehicle or an object on that side

    Body that hangs behind the rear axle swings the opposite way to the turn, so the tail of the truck sweeps out into the next lane or over the curb.

  47. 47. Where is a dunnage bag used and how does it work?

    Show answer

    Answer D: Between pieces of cargo inside a van, where it is inflated to take up the gap

    A dunnage bag is placed in the void between loads and inflated so the cargo is wedged and cannot move as the vehicle rolls and brakes.

  48. 48. How does overloading affect the way a vehicle drives?

    Show answer

    Answer C: It slows the vehicle on upgrades, makes stopping take longer and can overheat the brakes on downgrades

    Extra weight demands more from the engine and the brakes, so the vehicle climbs slowly and needs much more distance to stop.

  49. 49. What tells a driver when to shift up in a vehicle with a manual transmission?

    Show answer

    Answer C: Engine speed in rpm together with road speed

    Shift points are judged from engine rpm and road speed, using the operating range the manufacturer specifies for that engine.

  50. 50. During a stop you find a package in the trailer leaking an unknown chemical. What should you do?

    Show answer

    Answer C: Keep clear, keep others away and get help without touching the package

    A driver without the training and equipment does not handle a leak; the job is to protect people from the material and get qualified help to the scene.