Nevada DMV CDL General Knowledge Practice Test 8
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. Which exhaust system condition must be reported as a defect?
Show answer
Answer B: A section repaired by wrapping tape or patching material around the pipe
Exhaust parts may not be patched with wrap or tape, because the repair does not contain the gas or the heat and it fails quickly in service.
-
2. On a scale, your loaded truck is well under the gross weight limit, but one axle is above the limit for that axle. What does this mean?
Show answer
Answer D: The vehicle is overloaded and the load must be shifted or reduced before you drive on
Each axle and axle group has its own limit and each must be respected; being under the gross limit does not excuse an overloaded axle.
-
3. How is a shipping container normally secured when it is carried on a special container chassis?
Show answer
Answer B: With its own locking devices that attach the container directly to the chassis frame
Containers built for rail or ship transport have locking corners that fasten to a matching chassis; a container carried on a plain flatbed must be secured like any other cargo.
-
4. The coolant temperature gauge climbs above its normal range on a long grade. What is the correct response?
Show answer
Answer C: Stop when it is safe to do so and find the cause before going on
Rising coolant temperature signals a fault such as a lost belt, a leak or a blocked radiator, and continuing can turn a repair into a destroyed engine.
-
5. What should be done before a night trip to get the most from your headlights?
Show answer
Answer C: Clean the windshield, the mirrors and the lights
Dirt on glass and lenses cuts both the light you throw down the road and the light that reaches your eyes, so cleaning is the cheapest night safety measure there is.
-
6. Why is a quick lane change particularly risky with a load of hanging meat or of livestock?
Show answer
Answer A: The load swings or leans and can keep pushing the trailer after you straighten out
A swinging or leaning load keeps moving after the vehicle has finished the maneuver, so its momentum acts on the trailer at the worst moment.
-
7. At the end of the day you find no defects on a property carrying vehicle. What does the federal rule require?
Show answer
Answer B: No written report is required, although the carrier may still ask for one
For property carrying vehicles the report is required only when a defect or deficiency is found or reported, although a carrier may impose a stricter policy.
-
8. In very hot weather, how often should you check the tires during a trip?
Show answer
Answer D: About every two hours or every 100 miles
Heat raises tire pressure and can lead to blowouts, so tires are checked about every two hours or 100 miles when it is very hot.
-
9. You are drifting in the lane, yawning constantly and cannot remember the last few miles. What is the only reliable cure?
Show answer
Answer C: Stopping in a safe place and sleeping
Those are classic drowsiness warning signs, and nothing except sleep repays the sleep the body is missing.
-
10. Besides being uncomfortable, what can a series of hard, jerky brake applications do to a loaded combination?
Show answer
Answer A: Shift the load and push the trailer out of line behind the tractor
Sudden, uneven braking can move cargo forward and upset the alignment of a trailer, which is why stops should be made smoothly.
-
11. Why must the downshift be finished before you reach a steep downgrade or a sharp curve rather than during it?
Show answer
Answer D: Because once your speed is too high you may not get into any gear at all
If you wait until speed has built up, the lower gear may refuse to engage and you can be left in neutral with no engine braking at all.
-
12. During the walkaround inspection, where does the driver normally start and how does the check proceed?
Show answer
Answer C: At the left front of the vehicle, working around it in a set order that returns to the cab
The walkaround follows the same route every time, starting at the left front and circling the vehicle, so that nothing is skipped when the driver is tired or rushed.
-
13. What must be true of the person who performs the annual periodic inspection?
Show answer
Answer D: They must meet the federal qualification requirements for an inspector
The inspection has to be done by someone who meets the federal training and experience requirements for inspectors, whoever employs them.
-
14. Which vehicle condition makes hydroplaning more likely?
Show answer
Answer C: Tires that are worn or underinflated
Tread depth and correct pressure are what let a tire push water aside, so worn or soft tires lift onto the water film at lower speeds.
-
15. How do you avoid the sharp lurch that comes at the very end of a stop in a heavy vehicle?
Show answer
Answer A: Ease off the brake pressure just before the vehicle actually comes to rest
A smooth stop is finished by reducing pedal pressure as the vehicle settles, so the suspension does not rock the cab and the load forward.
-
16. What are the rules for using your turn signal before a turn or lane change?
Show answer
Answer A: Signal early, keep the signal on until the turn is finished, then cancel it
An early, continuous signal tells others what you plan to do; cancelling afterward keeps the signal from misleading them.
-
17. What must the driver check about the seat belt during the inspection?
Show answer
Answer A: That it is securely mounted, adjusts properly and is not ripped or frayed
A belt only restrains the driver if its anchorage is sound and the webbing is intact, so mounting and condition are both checked.
-
18. What is the purpose of blocking placed against cargo on a trailer deck?
Show answer
Answer B: To fill the space around the cargo so it cannot slide
Blocking is shaped to fit snugly against the cargo and fastened to the deck, removing the room the load would need in order to move.
-
19. During the walkaround you notice a bulge in the sidewall of a trailer tire. What does it indicate?
Show answer
Answer B: Damage inside the tire, which can lead to a sudden failure
A bulge means the internal structure has broken and only the rubber is holding the air, so the tire can burst without warning.
-
20. The shipper hands you the placards for a load that needs them. Who puts them on the vehicle?
Show answer
Answer C: The driver, who must also make sure they are the correct ones and are readable
The shipper supplies the placards, but it is the driver who must place them on the vehicle and confirm that they match the load and can be read.
-
21. The paperwork shows a weight, but the load looks heavier than you expected. What should you do?
Show answer
Answer C: Weigh the vehicle, since you are the one answerable for driving it overweight
The driver is the one who can be cited for an overweight vehicle, so a doubtful weight is settled on a scale before the trip continues.
-
22. A car that passed you on the right slows and stays alongside your trailer. What is the best response?
Show answer
Answer D: Ease off the accelerator so the car can move clear
A vehicle sitting beside a trailer is in a blind area and has nowhere to go if you need the lane, so the safest fix is to let it get ahead or behind.
-
23. A tire has a cut deep enough to expose the body ply or the belt material. What does that mean?
Show answer
Answer D: The vehicle must not be driven on that tire
Once the structural plies are exposed the casing has lost its strength, and federal rules treat that tire as unfit for the road.
-
24. You are making a right turn and cannot complete it without swinging into the oncoming lane. An oncoming car is approaching. What should you do?
Show answer
Answer A: Wait and let the oncoming vehicle pass before completing the turn, and do not back up
The oncoming vehicle has the lane; backing up in traffic is dangerous, so hold your position and finish the turn once the way is clear.
-
25. Where is the yellow antilock brake malfunction lamp on a trailer, and what does it mean if it stays lit?
Show answer
Answer D: On the left side, at the front or rear corner, and it means the antilock function may not be working
Trailers carry the yellow lamp on the left side, and a lamp that stays on after the bulb check means the antilock function may be lost even though the normal brakes still work.
-
26. During a trip you stop for a break. Which items should you check before driving on?
Show answer
Answer B: Tires, wheels and rims, brakes, lights, reflectors, electrical connections and cargo securement
Critical items can change during a trip, so each stop is used to recheck the tires, wheels, brakes, lights, connections and cargo.
-
27. You drive a 40 foot straight truck at 50 miles per hour in good conditions. What following distance does the rule of thumb call for?
Show answer
Answer A: 5 seconds
One second for every 10 feet of vehicle length gives 4 seconds, and one extra second is added for speeds above 40 miles per hour.
-
28. On a one way street or a divided highway, where are the warning devices placed?
Show answer
Answer B: About 10 feet, 100 feet and 200 feet back toward the approaching traffic
When traffic can only come from one side, all three devices are spread out behind the vehicle to give approaching drivers a longer warning.
-
29. What is the risk when too little weight rests on the drive axles?
Show answer
Answer A: Poor traction, so the drive wheels spin easily on wet or slippery surfaces
Traction depends on weight pressing the driving tires onto the road, so a light drive axle spins on wet, snowy or loose surfaces.
-
30. What tells you that an air suspension bag has a problem?
Show answer
Answer B: The bag is leaking or damaged, or the vehicle sits unevenly on that side
An air bag that leaks or is cut lets that corner of the vehicle settle, which throws the load onto the other suspension parts and changes the ride height.
-
31. Two vehicles of exactly the same length make a right turn, one gently and one very tightly. What is the effect on off-tracking?
Show answer
Answer A: Turning more sharply increases off-tracking, so the tight turn needs more room
Off-tracking depends on both the length of the vehicle and the sharpness of the turn; a tighter corner brings the rear wheels further inside the path of the front wheels.
-
32. Which brake lining condition must be reported?
Show answer
Answer C: Linings that are worn thin, loose, cracked or soaked with oil or grease
Linings must have enough material left and must be securely attached and clean, because a thin, loose or contaminated lining cannot deliver its share of braking.
-
33. You want to check whether a tire on your truck is properly inflated. What is the correct method?
Show answer
Answer A: Measure the pressure with a tire gauge
Only a tire gauge tells you the actual pressure; a tire can look and sound normal while being badly underinflated.
-
34. Federal rules forbid operating a commercial vehicle in which condition?
Show answer
Answer C: In a condition likely to cause a crash or a breakdown
A defect that makes a crash or a breakdown likely has to be corrected before the vehicle is driven, not reported at the end of the trip.
-
35. You are backing a tractor-trailer in a straight line and the trailer starts to drift to the left. What is the standard correction?
Show answer
Answer D: Turn the top of the steering wheel a little to the left, toward the drift
Small corrections made in the direction the trailer is drifting bring it back into line; large or opposite movements make the drift worse.
-
36. The temperature is around freezing and the road looks wet. What is a practical way to tell whether it is icy?
Show answer
Answer C: Check for ice building up on the mirrors, antenna or the front of the vehicle
Ice that forms on the mirror, antenna or windshield is a warning that the road surface is freezing too, and black ice can look like a wet road.
-
37. Using the snub braking method on a downgrade, when does the driver release the brakes?
Show answer
Answer A: After speed has dropped about 5 mph below the safe speed
The driver brakes firmly to about 5 mph under the chosen safe speed, releases to let the brakes cool, then repeats when the safe speed returns.
-
38. A commercial vehicle stops on the shoulder of a one-way or divided highway. Where do the three warning devices go?
Show answer
Answer A: At 10 feet, 100 feet, and 200 feet back toward approaching traffic
Traffic arrives from one direction only, so all three devices are set back toward it at 10, 100, and 200 feet, and they must be out within ten minutes.
-
39. What should you do with the previous driver vehicle inspection report before starting your trip?
Show answer
Answer B: Review it and confirm that listed defects were certified as repaired or as not needing repair
Reviewing the last report and the carrier certification tells you whether reported defects have been corrected before you take the vehicle out.
-
40. A chain rated at 6,600 pounds is fitted with a hook rated at 4,700 pounds. What is the working load limit of that assembly?
Show answer
Answer A: 4,700 pounds, the rating of the weakest part
An assembly is only as strong as its weakest component, so hooks, binders and links all count and the lowest rating governs.
-
41. An angry driver has cut in front of you and is now braking hard to provoke you. What is the safest response?
Show answer
Answer D: Drop back, avoid eye contact and let the driver go
Giving an aggressive driver space and no response removes the conflict, while any answering gesture invites escalation you cannot control in a heavy vehicle.
-
42. Why do cracked spring hangers or badly worn shackles matter?
Show answer
Answer A: They allow the axle to shift out of its correct position under the vehicle
Hangers and shackles hold the spring, and therefore the axle, in place, so when they fail the axle can move and the vehicle may become uncontrollable.
-
43. A car is following you far too closely. What is the safest response?
Show answer
Answer A: Open up more space ahead so you can slow gradually, avoid sudden changes, and do not speed up
Extra room in front lets you slow smoothly instead of braking hard, which is exactly what the driver behind cannot cope with.
-
44. You are inspecting the vehicle alone and need to confirm that the stop lights work. Which method is correct?
Show answer
Answer A: Have a helper press the brake pedal, or apply the brake in a way that keeps it on while you check from outside
Stop lights are checked from outside the vehicle while the brakes are applied, so a helper or a brake held on is needed.
-
45. What do the U-bolts on a leaf spring suspension do?
Show answer
Answer A: They clamp the spring assembly to the axle so it cannot move
U-bolts hold the spring pack tight against the axle, and a loose or broken U-bolt lets the axle slide out of place under load.
-
46. What must be checked about the cargo doors and any tarpaulin before a trip?
Show answer
Answer B: That the doors are closed and latched and that any tarp is tied down securely
An unlatched door or a loose tarp can swing open or tear free at speed, spilling cargo or blocking the view of the traffic behind you.
-
47. How do you test for leaks in a hydraulic brake system during the pre-trip inspection?
Show answer
Answer A: Pump the pedal three times, then hold firm pressure for five seconds and make sure the pedal does not move
If the pedal sinks while you hold pressure, fluid is escaping or air is in the lines, and the vehicle must not be driven until the problem is repaired.
-
48. Which of these is NOT on the federal list of parts and accessories the driver must be satisfied are in good working order before driving?
Show answer
Answer D: The seat cushion upholstery
The federal pre-trip rule names brakes, steering, lights and reflectors, tires, horn, wipers, mirrors, coupling devices, wheels and rims, and emergency equipment; seat upholstery is not on that list.
-
49. How does the working load limit of a tiedown relate to the force that would break it?
Show answer
Answer B: The working load limit is a fraction of the breaking strength and is the figure you use
The working load limit is set well below the point at which the device would fail, and securement is always calculated from the working load limit, never from breaking strength.
-
50. What should be checked about the power steering system in the engine compartment?
Show answer
Answer D: That the fluid level is correct and the hoses and pump are not leaking
Losing power steering fluid means losing steering assistance, which can happen suddenly and makes a heavy vehicle very hard to turn.